MI CNC Parts Get a Quote

Material

Custom CNC Machined 4140 Steel Parts

4140 steel parts machined to your print, annealed or prehardened.

Custom 4140 steel parts are loaded shafts, pins, spindles and fixture details machined to your print from 4140, a chromium-molybdenum alloy steel, annealed or prehardened, as your print names. It is the grade for a part that needs more strength than a plain carbon steel gives. There is no minimum, from one piece to production runs of 10,000. Send a STEP file and a PDF print through the quote form, and a person quotes it in 24-48 hours.

Updated November 2026

Steel

Mild, alloy, and tool grades. It rusts bare, so name a finish on the print.

Strength
Weight (lower is lighter)
Machinability

Typical parts

  • Shafts & axles
  • Hubs & couplings
  • Dies & tooling
  • Structural brackets
Quote a part in it

Before you send it

No C of C or material certifications ship with parts by default. If your PO needs them, say so before the quote. Inspection reports on critical dimensions aren’t included by default. If you need one, ask when you place the order.

What ships with an order covers inspection, inspection reports and certificates in one place.

If a part doesn’t match the print, it’s remade or credited.

When a part should be 4140

Name 4140 when a shaft, pin or tooling detail is loaded past what 1018 will carry. The steel page sets the grades side by side.

Properties of 4140, annealed and prehardened

The figures belong to the condition and the section size, so the print has to name both.

4140 steel properties as published (sources 1 and 2). Reference only; the print and its material specification govern.
ConditionTensile strengthYield strengthBrinell hardnessWhere it comes from
Annealed (estimated)95,000 psi60,500 psi197Producer data book (source 1)
Heat treated, 10 to 100 mm section930 to 1,080 N/mm2740 N/mm2 minimum269 to 331Producer data sheet (source 2)
Heat treated, 101 to 250 mm section850 to 1,000 N/mm2665 N/mm2 minimum248 to 302Producer data sheet (source 2)

Annealed or prehardened: what should the print say?

Write the grade and the condition: 4140 annealed, or 4140 prehardened with the hardness range you need.

If the part is to be welded, say so on the print. Position, perpendicularity and runout callouts are quoted from the print. Other alloys and plastics quoted on request. Name the grade on the print.

Parts machined from 4140, and the finish they get

Turned 4140 shows up as shafts, journals and pins, with ground diameters quoted through precision grinding. Milled 4140 shows up as tooling details, keys and the loaded details of fixtures.

Carbon and alloy steels need a finish for service, and the steel page covers rust and what stops it. A finish called out on the print is quoted with the part.

Ordering: what to send and quantities

  • What to send. A STEP file with no drawing is quoted to a ±0.005 in general tolerance, or the one your notes name, so a tighter bore or fit needs a drawing or a note.
  • Quantities. Ask for more than one quantity, such as 1, 25 and 100, and the quote shows each. Prototype first, then the run: prototype CNC machining covers the first piece and small-batch CNC machining the run that follows.
  • Files, payment and lead time. How to order CNC parts and what ships with an order cover files, payment, vendor setup, blanket orders and lead time.

Questions

Before you send a job.

01 How strong is 4140 steel?

It depends on the condition. A producer’s data book estimates annealed 4140 at 95,000 psi tensile and 60,500 psi yield, and a producer’s data sheet gives heat treated 4140 a minimum yield of 740 N/mm2 and 930 to 1,080 N/mm2 tensile in sections 10 to 100 mm. Name the condition on the print.

02 What is prehardened 4140?

It is 4140 bar bought already heat treated, at a hardness chosen to give useful strength while the material can still be machined into finished parts. Put the hardness range you need on the print.

03 Can 4140 be welded?

A stockist’s data sheet says welding 4140 is not recommended because of the likelihood of quench cracking, and that if it must be welded it is preheated to 200 to 300 °C. If the part is welded after it ships, say so on the print so the condition can be chosen with that in mind.

04 4140 or 1018: which should the part be?

Name 1018 for a general steel part and 4140 when the part carries high loads. The same producer data book estimates cold drawn 1018 at 64,000 psi tensile and annealed 4140 at 95,000 psi. When the call is close, ask for both grades on one quote.

05 Can I order one 4140 steel part?

Yes. There is no minimum: one piece to production runs of 10,000. A single shaft or pin is a normal order, and one-off CNC machining covers how one piece is quoted.

Sources (3)

All accessed 10 November 2026. Where a figure here differs from your print, the print governs.

1. Gerdau Special Steel North America, steel data book (2023 version): gsn.gerdau.com/sites/gsn_gerdau/files/2024-11/Gerdau_Data_Bk_2023_Version.pdf (estimated mechanical properties of selected steels: 4140 annealed, 1018 cold drawn).

2. voestalpine High Performance Metals (Australia), data sheet "AISI 4140 / 1.7225 / G41400": voestalpine.com/highperformancemetals/australia/app/uploads/sites/265/2024/08/Datasheet-4140-2026-v2.pdf (mechanical properties, heat treated, by section size).

3. Atlas Steels, "Through-Hardening Low Alloy Steel Bar 4140 Grade Data Sheet", revised 10 September 2021: atlassteels.com.au/wp-content/uploads/2021/09/Through-Hardening-Low-Alloy-Steel-Bar-4140-Grade-Data-Sheet-10-09-21-1.pdf (hardness chosen for strength while keeping the ability to machine; welding not recommended, preheat 200 to 300 °C if it must be welded).

Get Started

Send us your files.
We’ll take it from there.

A quote in 24-48 hours, no minimums. Like the quote, and we’ll make your parts and ship them to you.

Get a Quote