MI CNC Parts Get a Quote

Material

Custom CNC Machined 1018 Steel Parts

1018 steel parts machined to your print, one piece or a production run.

MI CNC Parts quotes custom 1018 steel parts: shafts, pins, spacers, brackets and fixture details machined to your print from 1018, a plain carbon steel usually supplied as cold-finished bar. It is the grade to name for a general steel part that does not need the strength of an alloy steel. There is no minimum, from one piece to production runs of 10,000. Send a STEP file and a PDF print through the quote form, and a person quotes it in 24-48 hours.

Updated November 2026

Steel

Mild, alloy, and tool grades. It rusts bare, so name a finish on the print.

Strength
Weight (lower is lighter)
Machinability

Typical parts

  • Shafts & axles
  • Hubs & couplings
  • Dies & tooling
  • Structural brackets
Quote a part in it

Before you send it

No C of C or material certifications ship with parts by default. If your PO needs them, say so before the quote. Inspection reports on critical dimensions aren’t included by default. If you need one, ask when you place the order.

What ships with an order covers inspection, inspection reports and certificates in one place.

If a part doesn’t match the print, it’s remade or credited.

When a part should be 1018

Name 1018 for shafts, pins, spacers, brackets and fixture details that need to be steel but do not carry the loads that call for an alloy grade. When the part is highly loaded, compare 4140; when it is cut from plate, compare A36; the steel page sets the grades side by side.

What the print should say for a 1018 part

Write the grade and the condition: 1018 cold drawn, or 1018 hot rolled. The strength figures belong to the condition, and bar that is turned and polished or turned and ground has properties that correspond to the hot rolled values (source 1). Name the specification if your part needs one, such as ASTM A108 for cold-finished bar.

Mark the diameters and faces that set a fit, and leave the rest at the general tolerance. A ground diameter is quoted with precision grinding. Position, perpendicularity and runout callouts are quoted from the print. Other alloys and plastics quoted on request. Name the grade on the print.

Parts machined from 1018, and the finish they get

Turned 1018 shows up as shafts and pins, spacers, bushings and sleeves and custom fasteners. Milled 1018 shows up as brackets, blocks and the steel details of fixtures.

Carbon steel needs a finish for service, and the steel page covers rust and what stops it. A finish called out on the print is quoted with the part. Powder coating is the durable option for a part that will not be machined again.

Ordering: what to send and quantities

  • What to send. Any file type is accepted. A STEP model plus a 2D PDF drawing is ideal; IGES, SLDPRT, Parasolid, DXF, DWG, STL and ZIP all work, and a sketch, photo or new sample part can start a quote. A STEP file with no drawing is quoted to a ±0.005 in general tolerance, or the one your notes name, so a tighter bore or fit needs a drawing or a note.
  • Quantities. Ask for more than one quantity, such as 1, 25 and 100, and the quote shows each. Prototype first, then the run: prototype CNC machining covers the first piece and small-batch CNC machining the run that follows.
  • Files, payment and lead time. How to order CNC parts and what ships with an order cover files, payment, vendor setup, blanket orders and lead time.

1018 properties, hot rolled and cold drawn

The producer’s data book notes that its figures can generally be expected from bars 3/4 to 1-1/4 in and are not part of any specification unless the source of supply approves them. Design to the specification on your print.

1018 steel properties as published (source 1). Estimated minimum values for bars 3/4 to 1-1/4 in. Reference only; the print and its material specification govern.
PropertyHot rolledCold drawn
Tensile strength58,000 psi64,000 psi
Yield strength32,000 psi54,000 psi
Elongation in 2 in25 percent15 percent
Brinell hardness116126
Machinability (cold drawn 1212 = 100)not rated70
Carbon0.15 to 0.20 percent0.15 to 0.20 percent
Manganese0.60 to 0.90 percent0.60 to 0.90 percent

Questions

Before you send a job.

01 How strong is 1018 steel?

A producer’s data book gives cold drawn 1018 bar an estimated minimum tensile strength of 64,000 psi and yield strength of 54,000 psi, and hot rolled 1018 58,000 and 32,000 psi. Those are estimates for bars 3/4 to 1-1/4 in, so design to the specification on your print.

02 Is 1018 easy to machine?

It is rated 70 for machinability in the cold drawn condition, on a scale where cold drawn 1212, a free-machining steel, is 100. The grade matters less to the quote than the geometry, and CNC design mistakes covers the features that add machining time.

03 1018 or 4140: which should the part be?

Name 1018 for a general steel part, and 4140 when the part carries high loads. A producer lists annealed 4140 at an estimated 95,000 psi tensile against 64,000 psi for cold drawn 1018. When the call is close, ask for both grades on one quote.

04 Can I order one 1018 steel part?

Yes. There is no minimum: one piece to production runs of 10,000. A single part is a normal order, and one-off CNC machining covers how one piece is quoted.

05 Does 1018 steel rust?

Yes, like any carbon steel it needs a finish for service. Name the finish on the print and it is quoted with the part; the steel page covers the options, and stainless steel is the alternative when the part stays wet.

Sources (1)

All accessed 10 November 2026. Where a figure here differs from your print, the print governs.

1. Gerdau Special Steel North America, steel data book (2023 version): gsn.gerdau.com/sites/gsn_gerdau/files/2024-11/Gerdau_Data_Bk_2023_Version.pdf (standard carbon steels, composition ranges: 1018 carbon 0.15 to 0.20, manganese 0.60 to 0.90; estimated minimum mechanical properties and machinability of carbon steel bars: 1018 hot rolled and cold drawn; ratings based on 100 for cold drawn SAE 1212; the note on bar sizes and on turned and polished bar).

Get Started

Send us your files.
We’ll take it from there.

A quote in 24-48 hours, no minimums. Like the quote, and we’ll make your parts and ship them to you.

Get a Quote