Material
Custom Machined A36 Steel Plate Parts
A36 plate parts machined to your print, one piece or a production run.
MI CNC Parts quotes custom A36 steel plate parts: base plates, mounting plates, brackets and weldment details machined to your print from A36, the common structural carbon steel plate. It is the grade to name when a part starts as plate and will be bolted or welded into a structure. There is no minimum, from one piece to production runs of 10,000. Send a STEP file and a PDF print through the quote form, and a person quotes it in 24-48 hours.
Updated November 2026
Steel
Mild, alloy, and tool grades. It rusts bare, so name a finish on the print.
Before you send it
No C of C or material certifications ship with parts by default. If your PO needs them, say so before the quote. Inspection reports on critical dimensions aren’t included by default. If you need one, ask when you place the order.
What ships with an order covers inspection, inspection reports and certificates in one place.
If a part doesn’t match the print, it’s remade or credited.
When a part should be A36
Name A36 when the part is cut from plate and its job is structural: a base plate, a mounting plate, a gusset or a machined detail that gets welded into a frame. When the part is turned from bar, compare 1018; when it is highly loaded, compare 4140. The steel page sets the grades side by side.
What the print should say for a machined A36 plate part
Say which faces are machined and which stay as rolled. A36 plate is hot rolled: its thickness, width and length tolerances follow ASTM A6 (source 1), and its surface carries mill scale. A face that has to be flat, a thickness that has to hold a tolerance and any datum face need to be called out as machined, with the flatness or thickness you need on the print.
Write the grade as A36 and name the specification if your part needs it. Position, perpendicularity and runout callouts are quoted from the print. Other alloys and plastics quoted on request. Name the grade on the print.
Machined, laser cut, or both?
A plate part with pockets, bores, tapped holes or a machined face is a milled part. A flat profile with through holes is a laser-cut part, and laser-cut steel parts covers A36 plate cut that way. One order can hold both kinds, and a profile can be laser cut and then machined where a feature needs it.
A36 details for weldments are covered on machined parts for fabrication and welding shops, and steel fixture bases on steel fixtures. Carbon steel needs a finish for service: a finish called out on the print is quoted with the part, and the steel page covers rust and what stops it.
Ordering: what to send and quantities
- What to send. Any file type is accepted. A STEP model plus a 2D PDF drawing is ideal; IGES, SLDPRT, Parasolid, DXF, DWG, STL and ZIP all work, and a sketch, photo or new sample part can start a quote. A STEP file with no drawing is quoted to a ±0.005 in general tolerance, or the one your notes name, so a tighter bore or fit needs a drawing or a note.
- Quantities. Ask for more than one quantity, such as 1, 25 and 100, and the quote shows each. Prototype first, then the run: prototype CNC machining covers the first piece and small-batch CNC machining the run that follows.
- Files, payment and lead time. How to order CNC parts and what ships with an order cover files, payment, vendor setup, blanket orders and lead time.
A36 plate properties
The minimum is the number a design uses. A Federal Highway Administration handbook notes that steel delivered as Grade 36 typically has a strength closer to 50 ksi than 36 ksi, which is a reason not to count on the minimum as the actual value in either direction.
| Property | Published value | Where it comes from |
|---|---|---|
| Yield strength, minimum | 36 ksi | Producer data sheet, plate 0.100 to 6.00 in (source 1) |
| Tensile strength | 58 to 80 ksi | Producer data sheet (source 1) |
| Elongation in 2 in, minimum | 21 percent | Producer data sheet (source 1) |
| Elongation in 8 in, minimum | 18 percent | Producer data sheet (source 1) |
| Modulus of elasticity, structural steels | 29,000 ksi | FHWA handbook (source 2) |
| Density, carbon and low-alloy steels | 0.283 lb/in^3 (7.84 g/cm^3) | Producer data book (source 3) |
Questions
Before you send a job.
01 How strong is A36 steel?
A producer’s data sheet gives A36 plate a minimum yield strength of 36 ksi and a tensile strength of 58 to 80 ksi. Design to the minimum in the specification on your print.
02 Is A36 the same as mild steel or 1018?
No. A36 is a structural steel specification for shapes, plates and bars, with a minimum yield of 36 ksi. 1018 is a carbon steel grade defined by its chemistry and usually bought as cold-finished bar; a producer estimates cold drawn 1018 at 54,000 psi yield. Use A36 for plate parts and 1018 for bar parts.
03 Can A36 parts be welded after machining?
A36 is a weldable structural steel, and ASTM’s scope covers welded construction. The welding itself stays with you unless the whole job is one order; machined parts for fabrication and welding shops covers how that works.
04 Can I order one A36 plate part?
Yes. There is no minimum: one piece to production runs of 10,000. A single base plate is a normal order, and one-off CNC machining covers how one piece is quoted.
Related
Where to go next.
Steel Parts
The steel grades side by side.
View →Laser-Cut Steel Parts
A36 plate and 1008 sheet, cut to a profile.
View →1018 Steel
The bar grade for turned and milled parts.
View →Fabrication & Welding Shops
Machined details for weldments.
View →Get a Quote
STEP + PDF in, numbers back in 24-48 hours.
View →Sources (3)
All accessed 10 November 2026. Where a figure here differs from your print, the print governs.
1. SSAB, "Data sheet ASTM A36", 20 May 2019: ssab.com/en-us/brands-and-products/commercial-steel/structural-steel/astm-a36 (plate 0.100 to 6.00 in: yield minimum 36 ksi, tensile 58 to 80 ksi, elongation minimums; thickness, width and length tolerances in accordance with ASTM A6).
2. Federal Highway Administration, Steel Bridge Design Handbook, "Bridge Steels and Their Mechanical Properties", Publication No. FHWA-IF-12-052, Vol. 1, November 2012: rosap.ntl.bts.gov/view/dot/49740 (A36 as weldable carbon-manganese structural steel; Grade 36 delivered strengths; defects hidden by mill scale; E taken as 29,000 ksi for structural steels).
3. Gerdau Special Steel North America, steel data book (2023 version): gsn.gerdau.com/sites/gsn_gerdau/files/2024-11/Gerdau_Data_Bk_2023_Version.pdf (physical constants: carbon and low-alloy steels 0.283 lb/in^3, 7.84 g/cm^3).
Get Started
Send us your files.
We’ll take it from there.
A quote in 24-48 hours, no minimums. Like the quote, and we’ll make your parts and ship them to you.
Get a Quote